Last Updated on December 19, 2022 by tawhid
If you have a motorcycle with a broken neutral safety switch, there is a way to bypass it. This can be done by jumpering the two wires that go to the switch. You will need to locate the wires going to the switch and then use a jumper wire to connect them.
Once you have connected the wires, your motorcycle should start without any issue.
- The steps to bypass the neutral safety switch on a motorcycle are as follows: 1
- Locate the neutral safety switch on the motorcycle
- This is typically located near the gearshift lever
- Disconnect the wiring harness from the neutral safety switch
- Use a jumper wire to bypass the neutral safety switch by connecting the wires that were previously connected to the switch
- Test that the motorcycle will now start in any gear position by trying to start it in each gear
How to Test a Motorcycle Neutral Switch
If you’re like most motorcycle riders, you probably don’t give your neutral switch much thought. But, if it starts acting up, it can be a real pain. Luckily, testing your neutral switch is a pretty simple process that anyone can do.
To test your motorcycle’s neutral switch, first turn on the ignition. Then, shift the bike into first gear and hold down the clutch lever. With the clutch lever held down, push the start button.
If the engine starts, then the neutral switch is working properly. If the engine doesn’t start, then you’ll need to check the wiring to see if there are any loose connections or damaged wires.
Credit: klr6500.tripod.com
How Do You Bypass a Motorcycle Neutral Safety Switch?
Assuming you’re talking about bypassing the neutral safety switch on a motorcycle with an electronic ignition:
There are a few ways to do this, but the most common is to simply disconnect the two wires that lead from the switch to the ignition. This can be done by removing the seat and locating the wires (they will likely be different colors) and cutting them or using a wire stripper to remove some of the insulation so they can be pulled apart.
Another way is to use a jumper wire to connect the two wires going to the switch. This can be done by connecting one end of the jumper wire to one of the terminals on the switch, and then touching the other end of the jumper wire to the other terminal onthe switch.
Of course, bypassing or tampering with any safety features on a motorcycle (or any vehicle) is not recommended and should only be done if absolutely necessary.
Where is the Neutral Switch Located on a Motorcycle?
On most motorcycles, the neutral switch is located on the right side of the engine, near the bottom. It is often round and black, and has a white or green dot in the center. To find it, look for a wire coming from the ignition coil that goes to a small black box.
This is the neutral switch.
What Does a Neutral Switch Do on a Motorcycle?
When you hit the starter button on a motorcycle with a neutral switch, it doesn’t engage the engine. Instead, it shuts off the flow of electricity to the engine so that it can’t start. This is a safety feature that prevents the engine from unexpectedly starting up while you’re working on it.
Without a neutral switch, the engine would be able to start as long as there was power flowing to it. This could be dangerous if you were working on the motorcycle and forgot to disconnect the battery. With the neutral switch in place, you can rest assured that your motorcycle won’t accidentally start up while you’re working on it.
How Do You Bypass a Neutral Safety Switch on a Boat?
If your boat is equipped with a neutral safety switch, you can bypass it by following these steps:
1. Locate the switch. It is usually located near the engine, on the control panel, or on the steering column.
2. Disconnect the wires leading to and from the switch.
3. Using a jumper wire, connect the two wires that you just disconnected. This will bypass the switch and allow your engine to start even if it is in gear.
4. Once your engine is started, remove the jumper wire and reconnect the wires to the switch.
Bypassing a Motorcycle Neutral Safety – Janus Halcyon 250
Conclusion
In some cases, it may be necessary to bypass the neutral safety switch on a motorcycle. This can be done by disconnecting the wires that lead to the switch and connecting them together. This will allow the motorcycle to start in any gear, but it is important to note that this should only be done as a last resort and when absolutely necessary, as it can be dangerous.